基于儒可夫斯基变换的涡轮钻具叶片设计及性能分析

为提高涡轮钻具叶片使用性能和创新叶片设计理论,提出了基于儒可夫斯基保角变换法与经典水力翼型相结合的涡轮钻具叶片设计新方法,以?127涡轮钻具叶片为研究对象,运用搭建的涡轮钻具叶型参数化设计平台和自主设计的涡轮钻具性能测试台架,完成了5种翼型的造型设计,研究了5种叶片流场性能,开展了设计叶片的性能测试实验,对比分析了设计叶片与塔里木油田某型在役?127涡轮叶片的实际效能。实验及仿真结果表明,基于新方法设计的NACA-0012翼型加厚叶片在600 r/min转速及15 L/s流量的设计工况下,其单级扭矩达5.83 N·m,较相同条件下某在役?127涡轮的单级扭矩提高约6.4%,级效率提高约1.16%,整体性能有了实质提升。     

热处理工艺对30MnCrNiMo高强钢组织与性能的影响

借助全自动淬火膨胀仪测定钢的Ac₁、Ac₃相变点,通过对试验钢进行淬火+亚温淬火+回火热处理和淬火+回火热处理,研究了两种热处理工艺下30MnCrNiMo高强钢的组织与性能。结果表明:30MnCrNiMo高强钢的Ac₁、Ac₃相变点分别为653、807 ℃。采用淬火+亚温淬火+回火的热处理工艺所获得的马氏体和铁素体复相组织比直接淬火+回火得到的全马氏体组织更为细小、均匀,试验钢的屈服强度为1499 MPa,伸长率为14.0%,室温、-40 ℃冲击吸收能量分别为35.5和29.5 J,钢的塑性和冲击性能显著提升,有效改善了30MnCrNiMo高强钢的强韧性能。     

2.25Cr-1Mo与2.25Cr-1Mo-0.25V钢冷却转变对比分析

采用相变仪、光学显微镜及扫描电镜研究了2.25Cr-1Mo和2.25Cr-1Mo-0.25V钢冷却转变过程,并分析了钒对其冷却转变的影响。结果表明,与2.25Cr-1Mo钢的CCT曲线相比,2.25Cr-1Mo-0.25V钢铁素体转变区及贝氏体转变区均向右移,并且在现有试验条件下已无法观察到珠光体转变区;钒添加到2.25Cr-1Mo钢中,能够提高钢的淬透性,2.25Cr-1Mo-0.25V钢在48 000 ℃/h冷速下能生成部分马氏体;钒能够细化钢板显微组织,与2.25Cr-1Mo钢相比,2.25Cr-1Mo-0.25V钢在800 ℃/h冷速下组织更为细小。     

Dynamic analysis of tapping mode atomic force microscope (AFM) for critical dimension measurement

Transient dynamics of tapping mode atomic force microscope (AFM) for critical dimension measurement are analyzed. A simplified nonlinear model of AFM is presented to describe the forced vibration of the micro cantilever-tip system with consideration of both contact and non-contact transient behavior for critical dimension measurement. The governing motion equations of the AFM cantilever system are derived from the developed model. Based on the established dynamic model, motion state of the AFM cantilever system is calculated utilizing the method of averaging with the form of slow flow equations. Further analytical solutions are obtained to reveal the effects of critical parameters on the system dynamic performance. In addition, features of dynamic response of tapping mode AFM in critical dimension measurement are studied, where the effects of equivalent contact stiffness, quality factor and resonance frequency of cantilever on the system dynamic behavior are investigated. Contact behavior between the tip and sample is also analyzed and the frequency drift in contact phase is further explored. Influence of the interaction between the tip and sample on the subsequent non-contact phase is studied with regard to different parameters. The dependence of the minimum amplitude of tip displacement and maximum phase difference on the equivalent contact stiffness, quality factor and resonance frequency are investigated. This study brings further insights into the dynamic characteristics of tapping mode AFM for critical dimension measurement, and thus provides guidelines for the high fidelity tapping mode AFM scanning.     

中控机房的改造思路

由于我台倒班方式，造成了技术管理分散，不利于人才的培养和电台健康的发展。为进一步提高电台安全播出管理水平，推进电台的自动化建设，充分利用现代化手段，对中控机房进行了改造。新模式的成功实施，能极大地提高我台安全传输发射水平。     

金川集团化工厂铜冶炼烟气制酸中温位余热回收

阐述金川集团化工厂530 kt/a铜冶炼烟气制酸系统扩能改造和余热回收前存在的问题,在遵循尽可能保留现有工艺管线和保证余热高效回收的原则上对转化工艺进行改造完善,将转化流程由原设计的“3+1/Ⅳ.Ⅰ-Ⅲ.Ⅱ”四段转化改为“3+2/Ⅴ.Ⅰ-Ⅲ.Ⅱ.Ⅳ”五段转化工艺流程,研发适合冶炼烟气制酸系统的分离型热管余热回收工艺技术.生产实践证明,该工艺在确保转化热平衡的基础上提升转化率,优化系统工艺技术指标,实现回收转化中温位富余热量生产饱和蒸汽,保证制酸系统与铜冶炼系统的匹配化生产,节能减排效益可观.     

如何实施社会转型期的民办高校品牌战略

在社会转型期，面对日益激烈的市场竞争环境，如何制定民办高效发战战略，引导民办高效的可持续发展，是关系到民办高校兴衰的关键。本文主要从民办高校品牌战略入手，对社会转型及高等教育转型进行论述，并对如何加强民办高校品牌建设进行探讨。     

Strong coupling effects during Cu/In/Ni interfacial reactions at 280 °C

The substantial heat generated in three-dimensional integrated circuits and high-power electronics has made thermal management a critical challenge for reliability in the electronics industry. Pure indium solder has been used as a thermal interface material to minimize the contact thermal resistance between a chip and its heat sink. Indium and indium-based alloys are potential lead-free solder for low-temperature applications. Heat sinks in the heat dissipation system as well as substrates of electronic joints are usually made of copper, with nickel being the most commonly used diffusion barrier on the chip side. Therefore, the Cu/In/Ni sandwich structure would be encountered in electronic devices. The soldering process for forming the Cu/In/Ni structure crucially determines the reliability of devices. In this study, Cu/In/Ni interfacial reactions at 280 °C were investigated. Intermetallic compounds were identified and the microstructural evolution was observed. A strong coupling effect between Cu and Ni was found, which caused several peculiar phenomena: (1) the formation of a Cu–In compound (the Cu₁₁In₉ phase) at the In/Ni interface; (2) the formation of two sub-layers of the Cu₁₁In₉ phase at the Cu/In interface; (3) the formation of faceted rod-like Cu₁₁In₉ grains; and (4) the formation of a half-Cu₁₁In₉, half-Ni₃In₇ microstructure after prolonged reactions. The mechanism of phase transformations is elucidated based on the calculated Cu–In–Ni ternary phase diagram using CALPHAD thermodynamic modeling.     

Data collection mode effect on feeling thermometer questions: A comparison of face-to-face and Web surveys

Feeling thermometer questions are widely used in political science research to estimate people’s attitudes and feelings toward a political object, like a political figure or an organization. Given the popularity of the feeling thermometer question in population surveys, more work is needed to explore the measurement of this question type. This study examines the data collection mode effect on feeling thermometers. Using the 2012 American National Election Studies, we find that the measurement of feeling thermometers is not exactly comparable between face-to-face and Web surveys. Face-to-face respondents tend to provide warmer feelings, while Web respondents give relatively more reliable responses in comparison. In both survey modes, respondents are most likely to select the response options that are verbally labeled although the effect is more striking in face-to-face than Web survey. The item nonresponse between these two modes does not differ in a meaningful way. This study ends by discussing future research directions on feeling thermometer questions.     

不锈钢马氏体转变的影响因素研究

对S30408和S30403两种牌号的奥氏体不锈钢板材在室温条件下进行单向拉伸试验,并用铁素体测量仪测量其马氏体相变量,结果表明随着拉伸变形量的增加,都诱发产生了形变马氏体,且随着变形量的增加形变诱发马氏体量迅速增加,并在拉断前逐渐趋于饱和。同时表明,随着含碳量增加马氏体转变量反而减小。